Skip to main content

The best 3D printers under $500

3D printers are finally affordable. Here are the best models under $500

The 3D printing market has seen quite a few changes over the last few years. In just the span of a decade, the barrier to entry has dropped from well over several thousand dollars to under $200 in some cases. However, all entry and mid-level printers are not made equal. We have a few suggestions for prospective buyers and other information regarding alternatives not found on this list.

To some veterans of the 3D printing scene, this list may seem like it lacks a few of the most commonly recommended printers for newcomers. This is by design. Our list only considers printers with tested components from proven, reliable vendors. That’s why we chose the Monoprice MP Mini v2 as our top pick–it’s reliable and easy to use. We have avoided any printer with a frame primarily made from interlocking acrylic pieces and anything historically unreliable.

Recommended Videos

Most bang for your buck: Monoprice MP Mini v2Monoprice MP Mini V2

Pros:

  • Reliable
  • Sturdy construction
  • Relatively easy to use for its price
  • Good customer support
  • Huge community

Cons:

  • Small build volume
  • Limited materials selection
  • Flexible materials infeasible
  • Fully manual calibration

The Monoprice Mini v2 is a ubiquitous entry-level printer these days, and at this price, it’s not hard to see why. While its build volume is among the smallest on this list, the Mini’s stability is not understated. Equipped with a full metal frame and a stout base, the MP Mini is rock-solid compared to most of the cheaper machines in its price range which tend to make heavier use of plastic frame components, which makes for a stellar out-of-box performer. Also, being from Monoprice gives the owner access to their excellent customer service and warranty.

The Monoprice Mini’s community is well established. It can offer plenty of advice on simple modifications that increase the machine’s longevity, to resources on replacement parts and additions. Its low-powered heatbed means it’s restricted to low-warp materials, and its remote extruder means flexible materials would be quite a challenge as well. However, its primary goal is to print with PLA (or PolyLactic Acid), a safe, environmentally friendly material, and in that regard, it absolutely shines.

Biggest build area for the price: Creality Ender 3 Pro

Creality Ender 3 Pro
Creality3d

Pros:

  • Relatively large build volume for its size
  • Quick and easy print removal
  • Large community
  • Wide variety of aftermarket upgrades
  • Fairly rigid construction

Cons:

  • Must be assembled
  • Bad customer support
  • Quality Control not great
  • Hit and miss out of the box performance

The Creality Ender 3 Pro is an upgrade of the popular Ender line of budget printers, with a few changes that improve its reliability, and that in fact, make it eligible for this list. The addition of a name-brand power supply means this device’s power output has been tested and certified to be stable for home use, which offers a fair bit of peace of mind over its predecessor.

It also adds a few welcome stability features and a magnetic build surface that can be taken off the printer to facilitate print removal. However, it is worth noting that Creality’s offerings have had quality control issues in the past, such as parts arriving damaged or tolerance errors from the factory, making for a difficult assembly.

The fact that it needs to be assembled is also worth mentioning. While by all accounts not a particularly challenging build, the Creality Ender 3 Pro does not come in a fully assembled state and does need to be built by the user before use is possible.

Big build area and great features: Monoprice MP Maker Pro

Monoprice MP Maker Pro
Monoprice

Pros:

  • Massive build volume for the price
  • Touchscreen interface
  • Automatic calibration
  • Removable magnetic bed
  • Flexible materials more feasible

Cons:

  • Requires a large dedicated space
  • Relatively small community
  • Maximum print speeds are much slower

The MP Maker Pro is big and feature-rich, to be sure. The leveling probe attached to the printhead means that it can automatically sense its bed’s shape, making leveling much simpler than on typical printers. Its magnetic bed allows for easy part removal, and the touchscreen makes for a much more modern-looking interface.

Its extrusion system uses a directly mounted motor, rather than the remote extruders seen on the past two printers, which allows for somewhat more precise plastic control out of the box. Additionally, it adds options for flexible plastics like TPU and TPE.

Its primary downside is that due to its immense size, the Monoprice MP Maker Pro is a slow printer. There is no avoiding the fact that moving a plate over 30cm wide in both directions back and forth requires a much lower rate of speed and acceleration than average, meaning prints will take much longer on this printer than on other, smaller machines.

Best resolution and surface finish: Anycubic Photon

Anycubic Photon Best 3D Printer 2018
Image used with permission by copyright holder

Pros:

  • Astonishingly great detail
  • Easy to use
  • Low maintenance
  • Does not require host computer for operation
  • Good manufacturer support

Cons:

  • Toxic resin fumes and byproducts.
  • Complex post-processing
  • Care is needed in handling
  • Resin has a high up-front cost

The AnyCubic Photon is notably different from the other printers on this list. All other machines listed here belong to the FFF (Fused Filament Fabrication) family of 3D printers, meaning they use melted plastic pushed through a heated nozzle. The Photon falls under the LCD subset of the DLP (Digital Light Projection) category. It uses light projected through an LCD to harden a vat of light-sensitive resin selectively.

This enables the Anycubic Photon to print at detail levels anywhere from four to ten times higher than standard filament-based printers, but this does come with downsides. The primary being that the liquid resin in its raw state is quite toxic, and thus, any photo-resin printer requires proper ventilation (preferably active in the form of a fan duct) at all times. However, if looking for a printer to make jewelry, figurines, or for other extremely high-detail purposes, the Photon is definitely the best pick on this list.

Best for speed and reliability: Monoprice Maker Ultimate

Monoprice Maker Ultimate
Monoprice

Pros:

  • Significantly faster than every other printer on this list
  • Stable calibration
  • Takes up relatively little space
  • Simple initial calibration
  • Material flexibility

Cons:

  • Reduced overall build volume
  • Limited upgrade paths
  • Lacks some comfort features

Yes, this is the third Monoprice printer on this list. In fairness, Monoprice only serves as a go-between with these printers — in fact, all three devices on this are rebrands of other machines by one of two Chinese companies. Monoprice does feature heavily in this article due to its quality control requirements, customer support, and use of safety-rated power components, unlike many comparable brands.

I must also admit a personal point of possible bias, namely that the Maker Ultimate is my own personal machine of choice. As of writing this article, my personal Maker Ultimate has run for approximately 590 hours of printing, creating everything from trash cans, greeting cards, phone cases, model planes, and, most commonly, other 3D printers. While it lacks automatic bed leveling, calibration is accomplished via a simple adjustment protocol. Due to its sturdy construction, this calibration tends to stay in place longer than most of its competitors at this price range.

In addition, the Monoprice Maker Ultimate has one advantage over every other printer on this list: Speed. Due to its design, a so-called “QuadRap,” where a small, square head moves on sets of intersecting rails, it has a significant edge against the other printers listed here, all of which fall into the lateral bed or “bed-slinger” category.

This is by no means an exhaustive list of the options in this price category but should serve as a good primer on safe, reliable devices. Whether you’re looking for an affordable first machine to give to a curious child (or a curious adult as well), an affordable option to stock a lab with, or maybe you’re just looking for something new to enhance your own creativity. It would be hard to go wrong with anything on this list.

Also, be sure to check out our list of the latest cheap 3D printer deals if you’re having trouble deciding what exactly it is you’re looking for.

James Lynch
Former Digital Trends Contributor
James has been enamored with technology and robotics as long as he can remember. His primary passion is for robots that make…
This 3D-printed four-legged robot is ready to take on Spot — at a lower price
3d printed ghost robotics origin

New Spirit 40: First Steps & Quick Run

Most people reading this will be familiar with four-legged robots such as the dog-inspired Spot robot developed by Boston Dynamics or Swiss robotics company ANYbotics’ ANYmal. But while there’s no doubt that such robots are supremely impressive, they’re also expensive -- which could limit their application in certain domains.

Read more
3D-printed replica of Michelangelo’s David statue is less than 1mm tall
3d printed david statue poppy seed

Towering in at a colossal 17-feet tall, Michelangelo’s David statue is a spectacular work of art. Well, it turns out that it’s no less impressive when it’s under one millimeter in size -- as experts from 3D-printing company Exaddon and the Laboratory of Biosensors and Bioelectronics at ETH in Zürich, Switzerland recently made clear.

In a dazzling demonstration, the collaborators teamed up to re-create the iconic David statue at two different (although both exceptionally tiny) scales. One was scaled down to 1:10,000, while the other was miniaturized even further to a scale of only 1:70,000. To put that pair of figures in context, the first one is around the same size as a poppy seed, just under 1 millimeter. The second one is around a tenth of a millimeter. Both are recognizable as the David statue, although the smaller of the two loses quite a few of the details of its much larger sibling. At that size, it’s hard to blame it too much, though!

Read more
Rivian tops owner satisfaction survey, ahead of BMW and Tesla
The front three-quarter view of a 2022 Rivian against a rocky backdrop.

Can the same vehicle brand sit both at the bottom of owner ratings in terms of reliability and at the top in terms of overall owner satisfaction? When that brand is Rivian, the answer is a resonant yes.

Rivian ranked number one in satisfaction for the second year in a row, with owners especially giving their R1S and R1T electric vehicle (EV) high marks in terms of comfort, speed, drivability, and ease of use, according to the latest Consumer Reports (CR) owner satisfaction survey.

Read more